Material Selection Process for a Low-Power Magnetically Shielded Hall Thruster
Published 2025 to AIAA Region II 2025 Paper...
Development and dosimetric evaluation of a modulatedintraoperative radiotherapy (mIORT) system using the Zeissintrabeam device
Paper published to IOPScience on 25 March 2025...
Sintering Mechanisms in Metal Extrusion-based Sintering-assisted Additive Manufacturing: State-of-the-Art and Perspectives
“Extrusion-based sintering-assisted additive manufacturing (ES-AM) has enabled the fabrication of intricate metal structures, spanning from...
Development of AF9628 Filament for Bound Metal Deposition Additive Manufacturing
“The Innovative Munitions Team’s task was to develop a cost-effective additive manufacturing (AM) method for...
Investigating the Influence of Infill Density and Postprocessing Parameters on 3D Printed PLA Copper Composite
Paper originally published to International Journal of Modern Manufacturing Technologies in 2024...
A Review of Fused Filament Fabrication of Metal Parts (Metal FFF): Current Developments and Future Challenges
Paper published to MDPI on 19 December 2024 https://www.mdpi.com/2227-7080/12/12/267...
Geometric and hardness characterization of additively manufactured copper using bound powder extrusion with thermal sintering
Full paper published to MATEC Web of Conferences in 2024 https://www.matec-conferences.org/articles/matecconf/pdf/2024/18/matecconf_rapdasa2024_07017.pdf...
Thermal-fluid modeling and simulation of Ti-6Al-4V alloy filaments during shaping in the hot-end of material extrusion additive manufacturing
“Continuous progress in material extrusion additive manufacturing is motivated by the need to produce functional...
3d printing of a continuous carbon fiber reinforced bronze-matrix composite using material extrusion
“The main objective of this study is to investigate, for the first time, the feasibility...
Enhanced Phase Change Heat Transfer with Fused Deposition Modeling (FDM) Printed Pit and Pillar (Pi2) Arrays
“Phase change heat transfer, crucial in thermal management systems, can be significantly enhanced through optimized...
Establishment of Select Printing Parameters for Low-Cost Fused Deposition Modeling Printed Cast Iron Through Experimental Optimization
“The fused deposition modeling (FDM) form of additive manufacturing provides a low-cost opportunity to quickly...
Experimental investigation of FDM manufacturing of 316 l stainless steel
Paper originally published to Springer Link 9 October 2024: https://link.springer.com/article/10.1007/s00170-024-14602-8...
A simple approach for additive manufacturing of inconel 718 with high densification level by fused filament fabrication
“In this study, a simple and low-cost approach to additively manufacture (3D print) Inconel 718...
Fracture Analysis of 316L Specimens Fabricated via Material Extrusion Additive Manufacturing: Influence of Building Orientation and Notch Acuity
Paper published to Wiley 20 September 2024 https://onlinelibrary.wiley.com/doi/pdf/10.1111/ffe.14463...
Shrinkage and deformation compensation in metal fused filament fabrication (mf3) sintered copper components using 3d scanning and inverse deformation
https://www.sciencedirect.com/science/article/abs/pii/S1526612524004316...
The role of crystallization and annealing on the thermal conductivity of material extrusion additively manufactured parts
“Despite the significant research being conducted on the mechanical reliability of additively manufactured parts, comparatively...
Optimization of extrusion-based additive manufacturing of bronze metal parts using a CuSn10/Polylactic acid composite
“As additive manufacturing gains widespread adoption across various industries, its application to traditional materials such as bronze...
Optimizing metal part distortion in the material extrusion-thermal debinding-sintering process: An experimental and numerical study
Paper published to Heliyon on 2 April 2024 https://www.cell.com/heliyon/pdf/S2405-8440(24)04930-2.pdf...
Characterization of Radiation Shielding Capabilities of High Concentration PLA-W Composite for 3D Printing of Radiation Therapy Collimators
“This work evaluates the radiation shielding capabilities of the PLA-W composite for MV energy photons...
A Design Strategy for Removing the Debinding and Sintering Gas in Additive Manufactured Samples of a Bronze/Polylactic Acid Filament
“To lower the cost of additive manufacturing of metallic components, the goal of this work...